Why Router Light is Blinking Green/Blue/Red/Yellow/Orange

WHY IS MY ROUTER BLINKING GREEN?

A blinking green light on the router indicates that your device is trying to connect. This connection can be via the USB or the Ethernet. The blinking should stop in a minute or two. However, if it does not happen:

Firstly, check the status of the service of your broadband. If it is slow, then you should wait for it to get an excellent connection. But if the connection is displayed to be strong, then follow the next steps.

Check that all the cables of the router are correctly connected.
Unplug the router’s power cable and plug it again to restart the router.
Wait for a few seconds while the router restarts. This should take a maximum of 5 minutes at most.

ADVICE – The router should display a solid green color by now. If it does not happen so and the blinking continues, contact your network provider.

WHY IS MY ROUTER BLINKING BLUE?

A blinking blue light on the router indicates that the router is ready to work and has set up your application’s Wi-Fi point. Once the connection establishes properly, the blinking will stop. The color will then change to solid green. If it does not happen:

Unplug the power cable to the router.

After doing so, the power button on the router should be pressed and held. Do it for 5 to 10 seconds. Once the time is up, immediately plug in the power cord back.

The blinking light will again appear. Hold on the power button till the blinking stops. This should take approximately 10 seconds.

ADVICE – The router should start working again after 3 to 5 minutes. If it does not happen so and the blinking continues, contact your network provider for the same.

WHY IS MY ROUTER BLINKING RED?

A blinking red light on the router indicates that the cables are not properly connected to the modem. It can also mean that proper electricity isn’t supplied to the router even if the connection is strong. In either case, the following steps can resolve this issue:

Switch off the router and unplug it.
Reset it by pressing the ‘Reset’ button and holding it for 10 seconds. Make sure that all the cables are connected to the proper places.
If there are any physical obstructions, move them.

ADVICE – Restart your router and wait for a few seconds to get a secure connection. If it does not happen and the blinking continues, contact your network provider.

WHY IS MY ROUTER BLINKING YELLOW?

A blinking yellow light on the router indicates that some errors have popped up while using the internet. This can further lead to disconnection. Usually, this issue gets resolved on its own after 5 to 10 minutes. However, if it does not happen:

Disconnect and unplug the power cable of the router. Let it stay in the disconnected mode for at least 20 minutes.
After 20 minutes, connect back the router and fully start operating before connecting to any device. This may take another 5 minutes.
Start connecting your devices one by one after the connection has been secured (indicated by solid green color).

ADVICE – The router should work properly now without further troubles. If it does not happen so and the blinking continues, contact your network provider for the same.

WHY IS MY ROUTER BLINKING ORANGE?

A blinking orange light on the router indicates a secure connection has not been established yet. The router is in the process of doing so. It can also mean that the router settings are not correct and/or issues in the hardware. This issue can be easily resolved by:

Turn off the router and unplug it. Then wait for a few minutes.
Check all the configurations and connections of the router in the switched-off mode. Ensure there are no physical obstructions.
Plug in the router and switch it on. Wait for a few seconds to get a good connection.

ADVICE – Sometimes the router blinks orange to indicate a new update. Make sure your router is up to date with the required changes. If the problem does not solve and the blinking continues, contact your network provider.

ROUTER LIGHT IS GREEN BUT NO INTERNET

A solid green light may not always indicate a good internet connection. Some hindrances aren’t allowing the device to get connected even if the router is securely connected.

First and foremost, ensure proper power supply to the router. In most cases, the problem will be resolved once power is established. But if the problem continues:
Unplug the router and plug it back after 2 minutes or so. Alternatively, you can restart it.
After it is switched on, check that the lines are fitted inside the right ports.
Connect to only one device and check that the connection has established.

ADVICE – The router should start working after the setup. Wait patiently for 30 seconds to 1 minute. If the problem persists, contact your network provider.

NETGEAR ROUTER COLOR MEANINGS

COLOR	MEANING
SOLID WHITE	ROUTER IS READY TO START
BLINKING WHITE	1. FIRMWARE OF THE ROUTER IS CORRUPTED 2. ROUTER IS RECEIVING AND/OR SENDING TRAFFIC
SOLID GREEN	THE CONNECTION IS STRONG AND CONNECTED
BLINKING GREEN	1. CONNECTION IS GETTING ESTABLISHED 2. SIGNALS ARE TRANSMITTING
SOLID AMBER	THE ROUTER IS GETTING SWITCHED/POWERED ON
BLINKING AMBER	1. ROUTER FIRMWARE IS UPGRADING 2. RESET BUTTON IS BEING PRESSED
SOLID ORANGE	INTERNET CONNECTION IS SLOW
BLINKING ORANGE	RE-ESTABLISHING SECURE INTERNET CONNECTION
BLINKING RED	NO CONNECTION/ CONNECTION LOST

NETGEAR ROUTER BLINKING ORANGE INTERNET LIGHT

When the internet connection is slow, it is indicated by a solid orange color on the Netgear router. When this same orange light starts blinking, it means the router is trying to re-establish the connection. Follow the steps mentioned below to solve this problem in no time.

Firstly check that your Netgear Nighthawk X10 AD7200 WIFI router is getting the power supply. If not, ensure that and the problem is solved. If yes, then go to the next step.
Check that the router’s settings are correctly configured and solve any network issue.
Restart the Netgear router. This would solve the issue.

ADVICE – In case the orange blinking light still appears, reboot both your router and the modem.

NETGEAR ROUTER BLINKING RED

If your Netgear router is blinking red light, it indicates no internet connection. The connection issue may be due to the overlapping of network sessions. If the router is moved from its original position, then also it blinks red light. Solve this issue by:

Check for new updates for your router. If that is so, simply disconnect the router from every device and do the update.
Check the Ethernet cable. Also, plug in the internet cable into a different port of the router.
Restart the router and wait for 5 to 10 minutes. Connect with devices if the problem is solved.

ADVICE – Certain times, the blinking red light appears if you’ve not made your payment for the internet services. Do keep the payments updated.

NETGEAR ROUTER BLINKING GREEN

A router like Netgear R6250AC1600 Wi-Fi router can blink green light sometimes. This implies that either signal is getting transmitted or the connection is getting established. The first situation is okay since you know you’re working without troubles. If it’s the latter case:

The issue is sorted mostly after you check the broadband service’s status. Contact them if trouble is from their end. If not, read ahead.
Disconnect all devices and restart the modem and the router.
Wait for at least 5 minutes before connecting.

ADVICE – This issue is minor and is usually resolved after restarting. But if it continues, contact your service provider.

NETGEAR ROUTER FLASHING RED POWER LIGHT

When the firmware of the router is either outdated or corrupted, it flashes a red power light. The flashing red light can be a warning sign of other errors too. For example, when some unspecified device or website is connected to the Netgear router, it flashes a red light.

The first thing to do is to install the latest version of the firmware. This can solve the matter and prevent it from happening again. But if it’s up to date and still blinking red:

Unplug the router and switch it off for at least 5 minutes.
‘Reset’ button should be pressed and held for 30 seconds or so. It restores the factory settings of the router.
Switch on the router. Set the IP address of all your devices to static before connecting again.

ADVICE – If the problem persists, contact your network provider.

NETGEAR ROUTER FLASHING BLUE LIGHT

A flashing blue light on the Netgear router indicates that it is unable to detect the modem. The modem is unresponsive to signals from the router. The flashing should stop eventually after a few minutes. But if it does not happen:

The router should be recovered by rebooting it. This process can approximately take 30 seconds to a minute.
Once it is switched on, wait for another minute before making connections.
The devices should be connected one by one after the router shows a solid green color.

ADVICE – This problem is quite rare and can be solved by the above steps. If it continues, contact your network provider.

LINKSYS ROUTER BLINKING WHITE LIGHT

Sometimes, a blinking white light on a Linksys MAX-STREAM MR7350 router can be noticed. It indicates that the router is trying to establish an internet connection. A blinking white light can also mean the self-diagnostic setup of the router during reboot. If the blinking stops after a few seconds:

Press and hold the ‘Reset’ button for 10 to 20 seconds.
Unplug and disconnect the router for at least one minute.
If the blinking has stopped, the router settings should be reconfigured.

ADVICE – A blinking white light can also mean software troubles. The above steps won’t help in that case. Contact your service provider.

LINKSYS ROUTER BLINKING ORANGE LIGHT

A blinking orange light on the Linksys router indicates an error in connecting the router to the modem. This issue can further lead to no internet connection which can hamper with your work.

Check all the connecting cables between the router and the modem before proceeding further to solve this issue.

Update the firmware of the Linksys router. After that reboot the system of your router.
Connect the router with the web browser of your laptop/computer. Reset the password of your router.
Also, change the IP address and restart the Linksys router.

ADVICE – Certain times cloning in the MAC address can cause the router to blink orange light. Check the clone settings of the MAC address.

LINKSYS ROUTER FLASHING GREEN LIGHT

The flashing of green light on Linksys WRT3200ACM router means signals are getting transmitted or connection isn’t very good. If the latter is the issue, then you would experience it while working on your device. A quick reboot can solve the issue, but if it continues:

Update the Linksys router. The light can indicate a new update. Without doing it you may not get a strong connection.
Assigning an IP address to your computer/laptop can be helpful. This IP address should be static.

ADVICE – This problem is very common and minor. But if it continues, contact your network provider.

HOW TO FIX ORANGE LIGHT ON TP-LINK ROUTER

If the internet connection is suddenly lost during usage, it is indicated by an orange light on the TP-link router. This can be a problem caused by either the router or the modem. Restart the modem and check. If it works well and still orange light blinks, then:

Unplug and restart your router. Then wait for a minute or so.
Do a factory reset. After that re-enter all your settings.
Reconnect the modem and the router with coaxial cable. This should restore the internet connection.

ADVICE – Try a cable of different quality if the problem isn’t resolved.

HOW TO FIX RED LIGHT ON TP-LINK ROUTER

The TP ARCHER A7 router displays a red light when there is no internet connection. It can also indicate a troubleshooting process or any physical obstruction for the router. To resolve this issue:

Reset your modem and check all the cables of your connections.
Update the firmware of the router. Once done, try to change its location.
Switch on the router and connect to one device. Connect to other devices once it’s assured that the issue has been solved.

ADVICE – Keep an eye on external factors like weather and electricity. These can also impact router functioning.

HOW TO FIX RED LIGHT ON DLINK ROUTER

The Dlink DSL-224 300 Mbps router shows a red light when the router encounters any kind of problem. A flashing red light indicates an error and a blinking red light indicates a troubleshooting process. The following steps would help resolve the issue:

Check all the connections. Make sure there are no weak or loose connections.
Unplug and disconnect your router. Plug it in after a few minutes.
Reset the router to the default factory settings. Then start using it.

ADVICE – Contact your network provider if the problem persists.

DLINK ROUTER FLASHING ORANGE POWER LIGHT

A fault in the firmware can cause damage to the router. When this damage gets resolved and recovered, the router blinks orange power light. This blinking stops after a few minutes, but if it does not happen so:

Upgrade to the latest firmware.
Set the static IP address on the laptop/PC to ‘192.168.0.2’. Then reset the router.
Browse your internet and select the firmware which you’ve downloaded. The issue would be sorted.

ADVICE – If the blinking continues, disconnect everything. Then wait for 5 to 10 minutes before connecting again.

DLINK ROUTER FLASHING GREEN LIGHT

A solid green light on Dlink DIR-1360 1300 Mbps router indicates a good connection. A flashing green light means that the router is trying to establish a connection. Usually, updating the firmware resolves the issue and the flashing stops. But if it does not happen:

Disconnect all the devices and reboot the modem and the router.
Wait for at least 10 minutes before switching it on. Once switched on, make sure to connect devices one by one.

ADVICE – The flashing green light can also mean the transmission of signals. In that case, you needn’t bother since your internet connection is good.

SPECTRUM ROUTER BLINKING BLUE

One can notice blue light blinking on the Spectrum router after a power outage. It takes time for the router to re-establish the internet connection. This blinking should turn to solid blue light once the connection is restored. However, if it does not happen so:

Disconnect all the devices. Unplug power and pull out the power cord.
Press and hold the ‘Power’ button for 10 to 20 seconds.
Plug in the power cord and switch it on after 5 minutes.

ADVICE – Check all the cable connections to ensure no wires are hanging loose.

SPECTRUM ROUTER BLINKING RED

When the Spectrum router does not initiate an internet connection, it blinks red light. The operating system is not normalized with the modem.

Ensure that all the wires are connected to the right ports and reboot the modem. If it doesn’t solve the issue:

Press and hold the ‘Reset’ button for 10 to 20 seconds. This button is at the back of the router.
Change the location of the router once it is switched on and update the firmware.

ADVICE – If any physical objects obstructing the router, move them away.