Home » Phones » Why are Sony WH-1000XM4 Headphones Making a Buzzing Noise?

Why are Sony WH-1000XM4 Headphones Making a Buzzing Noise?

Why is my Sony WH-1000XM4 headphones making a buzzing noise?

A buzzing noise on the Sony WH-1000XM4 headphones can occur because of compressed air bubbles in the earpads, condensation around the screws, wearing ear jewelry, or the Bluetooth range is out of reach.


  • Compressed air bubbles in earpads
  • Condensate water around the screws
  • Outdated software
  • Damaged headphone
  • Out of Bluetooth range limits
  • Environmental interference
  • Contact with metal jewelry in the ears


Buzzing noises coming from the WH-1000XM4 headphones are usually not signs of malfunctioning and do not pose a cause for concern. These noises can be overcome with some simple adjustments of the settings.


Sony WH-1000XM4 noise while walking

The Sony WH-1000XM4 headphone makes noise while walking because of the body vibrations. These vibrations get transmitted from the body to the headphone and cause the noise. 


You can try out the following steps to avoid the noise that gets triggered by your Sony WH-1000XM4 headphone while walking.

1. Check if the Noise Canceling feature has been activated in the headphone and if so, turn OFF this feature to stop the noise.

2. Watch out for an activated Ambient Sound Control feature and turn it OFF to put an end to the noise while walking.

3. Check if the firmware of the headphones is due for an update and update the firmware to its most recent version. This can take up to half an hour based on the size of the update and the Internet connection. Make sure that both earbuds have a minimum charge of 50% and that the Automatic Power Off feature is turned OFF during the update.

4. Reset and initialize the headphones once again. This may help to get rid of the noise when you use the headphones while walking.


How to fix the buzzing noise on Sony WH-1000XM4

The buzzing noise on the Sony WH-1000XM4 headphones is a result of condensation due to water droplets.


The tips given below can help to fix the buzzing noise on Sony WH-1000XM4 headphones.

1. Use a cotton ball to dry the headphones thoroughly. Pay special attention to drying the areas near the screws as there is a high chance of accumulation of water droplets around them.

2. Remove the screws to gain access to the inside of the headphone. Apply some Scotch mounting putty on each of the screws so that they get covered and don’t rust over time. Cover the mic as well if needed. You can also consider using insulating tape in place of the Scotch mounting putty to cover the screws.


How to fix static noise on Sony WH-1000XM4

The static noise on the Sony WH-1000XM4 headphone is because of condensation in the ear pads, or a turned ON noise canceling feature that results in no audio output due to an active amplifier.


The methods outlined here offer a walkthrough on how to fix the static noise on Sony WH-1000XM4 headphones.

1. Remove the screws on the headphone and take off the ear pads. Dry them thoroughly and eliminate all sources of water droplets using a cotton ball or a hair dryer. Apply a little mounting putty on each screw and fix the ear pads back in place by tightening the screws.

2. Turn OFF the Noise Canceling function in the headphone. 

You can do this by pressing the Custom button on your earpad twice or using the Sony headphone app installed on your smartphone or computer.


WH-1000Xm4 headphones making buzzing noise


How to fix clicking noise on Sony WH-1000XM4

The clicking noise on the Sony WH-1000XM4 headphone is due to a loose component or an activated noise-canceling feature. The noise may also be because of a Bluetooth-related problem or outdated firmware.


The steps below address various ways to fix the static noise on Sony WH-1000XM4 headphones.

1. Check for loose components like loose screws in the headphone and get them fitted securely to arrest the clicking noise.

2. Make sure that the Noise Canceling feature has been deactivated using either the headphone app or the Custom button on the headphone.

3. Ensure that the distance between the headphone and the corresponding audio source is not too much. The ideal distance between them shouldn’t be more than 30 feet.

4. Disconnect the Bluetooth connection between the audio source and the headphone and re-establish the connection. This disconnection and reconnection will help to clear up the cache and/or bugs that may be the reason for the clicking noise.

5. Look out for sources of external interference in the surroundings. If you notice such sources, try moving away from them when you use the headphones.

6. Watch out for a pending firmware update for the headphone and make sure that it’s always updated with the latest firmware.


How to fix crackling noise on Sony WH-1000XM4

The crackling noise on the Sony WH-1000XM4 headphone is because of compressed air bubbles within their earpads, moisture or water in the ear cups or around the screws, multipoint connectivity, or dust in the sensor. An activated headset function on the computer can also cause a crackling noise when the headphone is used with a PC.


The tips highlighted below guide you on how to fix the crackling noise on Sony WH-1000XM4 headphones.

1. Clean the ear pads or ear cups thoroughly using some cotton wool to remove all traces of moisture on them.

2. Apply some insulating tape or mounting putty over the screws that hold the ear pads in place to stop them from getting rusted due to instances such as sweat.

3. Remove both ear pads and place a small bag of silica gel under each of them to absorb the moisture in the future. It would be best if you remember to fasten the ear pads firmly in place after you keep the silica gel bags.

4. Connect the headphone to only one source at a time. If you have connected it to more than one source, disconnect the headphone from all the sources and turn it OFF for a while. Reconnect it to a single source.

5. Look out for dirt or dust accumulation in the sensor holes of the ear pads and get them removed at the earliest. This will resolve the issue if the crackling noise was due to debris affecting the sensor functionality.

6. Check the Sound settings of the PC to determine if the headset function has been activated. If so, you may want to turn it OFF. You may also want to uninstall players like Realtek, which can pave the way for this issue.


How to fix high pitched noise on Sony WH-1000XM4

The high-pitched noise on the Sony WH-1000XM4 headphone is because of improperly seated ear cushions, a low battery, or blocked ear cup ports. A loose battery cable can also cause a high-pitched noise in the headphone.


The steps outlined here let you know how to fix the crackling noise on Sony WH-1000XM4 headphones.

1. Check if the ear cushions of the headphone have moved out of place and seat them properly. You can consider pushing hard on the problematic ear cup till you hear a click sound that ensures proper seating.

2. Replace the existing battery of the earphone with a new and fully charged battery. If the high-pitched noise stops, the old battery was reaching the end of its lifespan and triggered the noise.

3. Look out for the possibility of blocked ear cups due to various reasons such as earwax buildup in them. Cleaning the ear cups to remove such foreign elements will help resolve the high pitched noise.

4. Check if the battery cable has a loose connection. If so, remove the cable and fasten it securely once again.

5. Seek the assistance of the customer service team to get the headphone serviced if it makes the noise even when it’s not being used.

Ernie Lo

Ernie Lo is a qualified web designer and web developer. He works as an IT support technician and website manager at Benleigh Vending, and he also fixes vending machines.

Recent Posts